15% off Comfrt — auto-applied at checkout, no code.
Get 15% Off →

Do You Need a Filament Dryer? When and How to Dry Filament

SUNLU SUNLU FilaDryer E2, Up to 110℃, Professional Drying and Annealing, Born for Engineering 3D Printing Filaments

Disclosure: We may earn a commission from purchases made through links in this article, at no extra cost to you.

SUNLU logo

SUNLU✓ Offers checked 19 Nov 2026
3% OFFDK26WO527RShow code

3% off select SUNLU collections with our exclusive code

Get this deal →

FREE SHIPPING

Free shipping on SUNLU US orders over $40

Get this deal →

The short answer

You need a filament dryer if you print nylon, PVA, TPU or PETG, live somewhere humid, or keep spools open for weeks. These materials absorb moisture quickly, and wet filament causes stringing, popping, rough surfaces and weak layers. If you mostly print PLA and use spools within a few weeks, you can often get by with good storage and dry a spool only when problems appear.

Filament drying at a glance

  • Most moisture-sensitive: nylon, PVA, TPU and PETG (Polymaker).
  • PLA starting point: 45°C for 6 hours; PETG 55°C for 6 hours; TPU 60°C for 4–6 hours (Prusa).
  • Typical signs of wet filament: popping, stringing, rough surfaces, weak layers.
  • Example dryer prices on Nov 19, 2026: $38.99 (SUNLU S1 Plus) to $267.99 (SUNLU E2).

Which filaments absorb moisture

All common filaments absorb some water from the air, but not equally. Polymaker’s wet-filament guide rates nylon, PVA, TPU and PETG as highly sensitive, ABS and some copolymers as moderate, and PLA as low but still affected over time. Prusa’s knowledge base lists polyamide, PP, PVA and BVOH as highly hygroscopic and recommends storing them dry or drying them before every print.

MaterialMoisture sensitivityWhat that means
PLALowDry only when you see symptoms or after long storage
PETGHigh (Polymaker)Dry before important prints; store sealed
TPU (flexible)HighOften needs drying; wet TPU strings badly
Nylon (PA), PVAVery highDry before every print and ideally print from a dry box

Signs your filament is wet

  • Popping, crackling or hissing at the nozzle as water turns to steam
  • More stringing and oozing than usual
  • Rough, pitted or bubbly extrusion and a dull surface
  • Weak layer adhesion or brittle parts
  • In severe cases, visible steam or smoke at the nozzle (Prusa)

Polymaker also advises drying any spool that has been sitting unused for a long time before you blame print settings.

Drying temperatures and times

Prusa publishes these starting points for its dryers and recommends not exceeding them, because filament can soften and stick together on the spool:

MaterialTemperatureTime
PLA / rPLA45°C (113°F)6 hours
PETG55°C (131°F)6 hours
TPU60°C (140°F)4–6 hours
ASA80°C (176°F)4 hours
PC Blend85°C (185°F)5 hours
PVB45°C (113°F)8 hours
PA11-CF (nylon composite)90°C (194°F)6 hours

Always check your filament maker’s data sheet first, since recommendations vary by brand and blend, and keep cardboard spools away from high temperatures.

Chart of filament drying temperatures for PLA, PVB, PETG, TPU, ASA and PC Blend
Drying starting points by material. Source: Prusa Knowledge Base (read November 19, 2026). Chart: Hnlsharing.

How to dry filament, step by step

  1. Identify the material on the spool label and look up its drying temperature in the maker’s data sheet; use the table above only as a starting point.
  2. Check the spool: cardboard spools and some plastic spools soften at higher temperatures, so stay at or below the recommended setting.
  3. Preheat the dryer to the target temperature, then load the spool so warm air can reach the filament.
  4. Dry for the full time. Prusa’s times range from about 4 to 8 hours for common materials; shorter runs may not reach the inner windings.
  5. Print from the dryer or seal it straight away in a bag or box with fresh desiccant.
  6. Run a short test print. Less popping, cleaner extrusion and less stringing usually mean the drying worked; if not, the problem may be your print settings.

Dryer, oven, dehydrator or dry box?

  • Dedicated filament dryer: designed for low, steady temperatures and often lets you print straight from the box. This is the simplest option if you dry regularly.
  • Food dehydrator: Polymaker notes it provides heat and airflow and can work for small spools, as long as the spool fits and the temperature is accurate.
  • Kitchen oven: Prusa warns that home ovens control low temperatures poorly; swings that do not matter for food can deform filament, especially PLA. Use a separate thermometer and never leave it unattended.
  • Dry box with desiccant: keeps dry filament dry, but does not actively remove moisture from a wet spool.

What filament dryers cost

Example US prices from the official SUNLU and eSUN stores, read on November 19, 2026:

DryerPriceMax temperature
SUNLU S1 Plus$38.99–$62.9955°C
SUNLU S4 Pro$139.9985°C
SUNLU E2$249.99–$267.99110°C
eSUN eBOX Lite$52.99Not listed

We list SUNLU and eSUN because their US stores showed current dryer prices when we checked; other filament brands, such as Polymaker and Creality, also sell dryers, so compare maximum temperature and capacity across brands. A basic single-spool dryer covers PLA, PETG and TPU. If you print nylon or engineering materials, look for a higher maximum temperature. Compare the two brands in our SUNLU vs eSUN guide.

How to choose a filament dryer

  • Maximum temperature: 55 to 60°C covers PLA, PETG and TPU in Prusa’s table; ASA (80°C), PC Blend (85°C) and nylon composites such as PA11-CF (90°C) need a hotter dryer.
  • Capacity: single-spool dryers suit one printer; multi-spool units help if you run several materials.
  • Print-through port: lets you print directly from the dryer, which matters for nylon, PVA and TPU.
  • Spool size: check that 1 kg spools (and larger spools, if you use them) fit with the lid closed.
  • Timer and humidity readout: useful for repeatable results and for knowing when to re-dry.

Shopping for a SUNLU dryer? Free shipping over $40 and our exclusive code are tracked on our store page, checked 19 Nov 2026.

See SUNLU deals →

How to store filament so it stays dry

  • Keep open spools in a sealed box or vacuum bag with fresh desiccant.
  • Give priority to the most sensitive materials: nylon, PVA, TPU, then PETG.
  • Reseal spools right after printing and recharge or replace desiccant when its indicator changes color.
  • For long prints with nylon or PVA, print from a dry box or a dryer that feeds filament directly to the printer.

Tip: label each sealed bag with the date you dried it. If a spool has been open for weeks and starts printing worse, drying it is the quickest thing to rule out before changing slicer settings.

How we researched this

This guide is research-based; we did not test these dryers. On November 19, 2026 we read the drying guidance in the Prusa Knowledge Base and Polymaker Wiki, and dryer listings on the SUNLU store and eSUN store. Temperatures are manufacturer starting points, not guarantees for every brand.

Frequently asked questions

Do I need a filament dryer for PLA?

Usually not right away. Prusa and Polymaker both describe PLA as much less sensitive to moisture than nylon, PVA, TPU or PETG. If an older PLA spool starts stringing, popping or printing rough surfaces, drying it at a low temperature (Prusa lists 45°C for 6 hours) often fixes it.

Which filaments need drying the most?

Nylon (PA), PVA, TPU and PETG. Polymaker rates these as highly moisture-sensitive and says they often need a dryer even during printing, and Prusa lists polyamide, PP, PVA and BVOH as highly hygroscopic.

How do I know if my filament is wet?

Common signs are popping or hissing at the nozzle, extra stringing and oozing, rough or pitted extrusion, bubbles, and weak or brittle layers. Prusa also mentions smoke or steam at the nozzle in severe cases.

Can I dry filament in a kitchen oven?

It is possible but risky. Prusa notes that home ovens control low temperatures poorly, and swings that do not matter for food can soften or fuse filament, especially PLA. If you try it, check the temperature with a separate thermometer and never leave it unattended.

What temperature should I dry PETG at?

Prusa lists 55°C for 6 hours for PETG, 60°C for 4 to 6 hours for TPU and 45°C for 6 hours for PLA. Going hotter than recommended can make filament soften and stick together on the spool.

Is a dry box the same as a filament dryer?

No. A dry box with desiccant keeps already-dry filament dry during storage or printing. A dryer actively heats the filament to drive moisture out. Many people use both.

The bottom line

If you print PETG, TPU, nylon or PVA, a filament dryer pays for itself in fewer failed prints. If you print mostly PLA and store it sealed, start with a dry box and dry only when you hear popping or see stringing. Follow the manufacturer’s temperature for each material and avoid using a kitchen oven unless you can monitor it closely.

Ha Ngoc Loc

about the author

Ha Ngoc Loc
Editorial Team

Ha Ngoc Loc is the founder and editor of Hnlsharing. Loc researches each brand from its official product pages, pricing, shipping, return and warranty policies, and from customer reviews on independent platforms such as Trustpilot. Hnlsharing does not buy or test products hands-on, so every review says it is research-based and shows the date its facts were checked. Coupons and deals come from brands and their affiliate programs, and each offer shows the date it was last checked on the brand's site.